The O-9310 can multiplex up to 4 T1 or E1 signals for transmission over an optical fiber, resulting in longer reach without repeaters and superior performance compared to copper media.
The O-9310 also supports an optional 10 /100 BaseT ethernet bridge port, an optional V.35, X.21, RS449/V.36, RS232/V.28 or EIA530 or EIA530(A) with DTE/DCE selection.
Available in a cost-effective non-CPU model with DIP switch setup or an intelligent model with SNMP and remote configuration capability. Basic non-manageable model without CPU provides system setup and loopback by DIP switches setting. Application for the Optical T1/E1 extender include fiber connected extensions for LAN, WAN, SONET/SDH, ATM and DLC.
Source MLM Laser System |
Gain 30 dB |
Wavelength 1310 ± 50 nm, 1550 ± 40 nm |
Line Code Scrambled NRZ |
Power -26 or -8 dBm |
Detector Type PIN-FET |
Receiver Sensitivity -38 dBm at BER < 10-10 |
Fiber Type Single mode |
Optical Line Rate 155.52Mbps |
Protection Optional 1+1 APS |
50 Km reach |
NOTE: Longer or shorter, 15 to 120Km, on special order. |
|
Optical Module |
Fiber Direction |
Wavelength (nm) |
Connector |
Distance (km) |
Power (dB) |
Single |
Dual uni-direction |
1310 |
SC (Subscriber Connector) |
30 |
20 |
|
|
1310 |
SC (Subscriber Connector) |
50 |
30 |
|
|
1310 |
FC (Fiber Connector) |
30 |
20 |
|
|
1550 |
SC (Subscriber Connector) |
20 |
12 |
|
|
1550 |
SC (Subscriber Connector) |
100 |
40 |
|
Single |
Single bi-direction (master) |
1310/1550 |
SC (Subscriber Connector) |
30 |
20 |
|
Single bi-direction (slave) |
1310/1550 |
SC (Subscriber Connector) |
30 |
20 |
For discussion on whether to choose uni-directonal or bi-directional fiber option, see the white paper here.
Number of E1 lines 4 |
Impedance 120 ohm twisted pair, 75 ohm for BNC |
Line Rate 2.048 Mbps +/- 50 ppm |
Connector RJ48C, BNC |
Line Code HDB3 |
Output Signal ITU G.703 |
Number of T1 lines 4 |
Line Rate 1.544 Mbps ± 50 bps |
Output Signal DSX1 |
Line Code AMI or B8ZS |
Framing D4/ESF (selectable) |
Input Signal ABAM cable length up to 655 feet |
Connector RJ48C |
10/ 100 Mbps half/ full duplex ethernet bridging and 22 Mbps operation on the HDLC port
ANSI/ IEEE Std. 802.1D MAC Bridging capabilities (without spanning tree algorithm)
Automatic MAC table learning and aging
Supports VLAN and extended Ethernet frame support
|
Port Number 1 |
Connector DB25S |
Data Rate Nx64kbps (N=1~32) |
Clock Mode External, Internal, Received (Selectable) |
Type Software-selectable V.35, X.21, RS449/V.36, RS232/V.28, EIA530 and EIA530A |
Connector RJ45 at rear panel |
Data Rate Up to 64Kbps async |
|
Connector DE9 on front panel
|
|
|
Protocol Telnet |
Electrical RS232 interface |
Connector RJ45 on front panel |
Protocol Menu driven VT-100 terminal |
|
Baud Rate 9600, 19200, 38400, 57600, 115200 |
|
Optical Fiber Local and remote loopbacks
T1 and E1 Lines Local and remote loopbacks
Dimensions 215 x 55 x 188 mm (W x H x D)
Mounting Stand-alone
Power Source (AC) 100 to 240 Vac, 50/ 60 Hz
Power Source (DC) 24Vdc: 18-36 Vdc ; 48Vdc: 36-72 Vdc
Power Consumption < 10 W
Temperature Range 0°C to 50°C
Humidity 0% - 95% RH (non-condensing)